Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Vacaville Homeowners
Most chimney damage announces itself before it becomes dangerous. A loose cap rattles in the wind, a crown cracks along its edge, or a dark stain spreads across the ceiling near the flue. We handle chimney repair in Vacaville so those small problems don’t turn into liner failures, water damage, or unsafe drafting. Our technicians have up to 9 years of experience working on masonry chimneys, factory-built fireplaces, and gas inserts across Solano County. We’re a chimney-only specialist, not a general contractor squeezing in a side job.

We schedule same-day appointments when the calendar allows, and our technicians carry the materials for most common repairs. You get a clear explanation of what’s wrong before any work starts, and a written estimate that sets the final price. Call (844) 797-8347 to get started. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Chimney Cap Installation
Chimney Cap Installation is the fitted lid that goes over the flue opening to keep rain, birds, squirrels, and debris out of the chimney. You need one if your flue is open to the sky, if nesting material keeps showing up during sweeps, or if water is finding its way down the tile. In Vacaville, the dry season followed by steady winter rain means an open flue can take on water for months without anyone noticing until the firebox stains. We install stainless caps and multi-flue caps that fit the exact dimensions of your chimney top, and we seal them to the crown so they don’t work loose. Typical installation runs about $185 to $450 depending on single-flue versus multi-flue, the height of the chimney, and the cap material. The written estimate sets the final price.
Single-Flue Versus Multi-Flue Caps
A single-flue cap sits over one opening and fits most fireplaces. A multi-flue cap spans a masonry chimney with two or more flues, with individual openings built into one top plate. We measure the full chimney footprint before ordering so the cap fits without gaps at the edges.
What a Cap Does During Fire Season
A cap stops floating embers from landing on the roof and blocking sparks from rising freely out of the flue. It also keeps the rain out during the wet months so the liner stays dry between fires. A fitted cap is the simplest piece of chimney protection you can buy.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement means removing a damaged, rusted, or missing cap and fitting a new one that actually seals the top of the flue. You need a replacement when you spot rust streaks down the stack, a cap sitting crooked after a windstorm, or a mesh screen that’s torn and letting birds through. Old galvanized caps are a common sight on older homes around Vacaville, and once the coating fails they rust from the inside out. We pull the old cap, check the spark arrestor screen and the last course of flue tile, and fit a new stainless cap sized to the opening. Typical replacement runs about $200 to $500, depending on access, chimney height, and whether the old cap has to be cut free. The written estimate sets the final price.
How We Remove a Stuck or Seized Cap
Caps that have rusted to the flue collar don’t come off by hand. We cut the fasteners and work the old cap free without chipping the flue tile underneath. If the collar itself is failing, we note that before the new cap goes on.
Checking the Crown Before the New Cap Goes On
A new cap only protects the flue if the crown beneath it is sound. We look at the crown surface and the caulk line while we’re up top. If the crown needs attention, you hear about it before we finish the job, not after the next rain.
Chimney Liner Installation
Chimney Liner Installation means putting a continuous flue lining inside the chimney to contain smoke, gases, and heat and to protect the surrounding structure. You need one when the clay tile liner is cracked, spalling, or missing, when the chimney was built with no liner at all, or when a new appliance needs a correctly sized flue. This is the repair category where a sweep-only service usually stops and refers you elsewhere. We install DuraFlex stainless liner systems sized to your appliance and your flue, the kind of professional-grade material that lasts under real firebox heat. A typical reline runs about $2,400 to $6,500 depending on liner length, diameter, insulation, and whether the flue needs prep work first. The written estimate sets the final price.
Why Sizing the Liner Correctly Matters
An oversized liner lets flue gases cool and draft poorly; an undersized one can’t handle the appliance’s output. We take the appliance rating and the flue dimensions into account before the liner is cut. Getting this wrong is the difference between a chimney that drafts and one that smokes into the room.
Insulated Liners in a Mild Climate
Insulation isn’t only for cold regions. A wrapped liner keeps flue gases warmer from the firebox to the top, which helps draft and reduces creosote buildup during the shoulder seasons. We fit insulation around the liner where the flue clearance allows.
Chimney Flashing Repair
Chimney Flashing Repair means fixing the metal and sealant layer where the chimney meets the roof, the place where most roof leaks around a chimney start. You need it when you see water stains on the ceiling near the chimney, rust streaks on the flashing, pulled or curled metal, or a gap where the counterflashing meets the brick. Vacaville roofs take strong summer sun, and sealant along the flashing edge hardens and pulls back over time. We cut out the failed sealant, reset or replace the flashing step by step, and use a roofing sealant rated for sun exposure. Typical flashing repair runs about $350 to $900, depending on whether we’re resealing or replacing the metal. The written estimate sets the final price.
Step and Counterflashing Explained
Step flashing weaves into the roof shingles along the chimney’s uphill side; counterflashing cuts into the mortar joint or sits over the brick. Both have to overlap correctly to shed water. When one part fails, the other usually needs a look too.
The Mortar Joint Connection
Counterflashing that’s set into a mortar joint only stays watertight if the mortar around it is intact. We check that joint while we’re on the roof. If the mortar has crumbled, the flashing fix won’t hold until that’s repaired too.
Chimney Crown Repair
Chimney Crown Repair means fixing the concrete or masonry slab that caps the top of the chimney and sheds water away from the flue. You need it when the crown has cracks, is crumbling at the edges, has pulled away from the flue, or is sloped the wrong way and puddling water. A failed crown is one of the most common ways water gets into a chimney in Vacaville, and the damage usually shows up much lower down, in the firebox or the ceiling below. We remove loose material, reshape the slope, and rebuild or resurface the crown with a weather-resistant mix, or use HeatShield where resurfacing is the right call. Typical crown repair runs about $450 to $1,200, depending on crown size and condition. The written estimate sets the final price.
Resurfacing Versus Rebuilding
A crown with surface cracks but a sound base can often be resurfaced. One that’s crumbling through its thickness or separating from the flue needs to be rebuilt. We tell you which one you’re looking at, with photos before we start.
Why the Slope Direction Matters
A proper crown slopes away from the flue so water runs off the edge instead of sitting against the tile. A flat or back-sloped crown holds water and feeds cracks. Reshaping the slope is part of most crown repairs we do.
Chimney Repair Companies
Chimney Repair Companies vary widely in scope, and it’s worth knowing what you’re choosing between before you book. Some are sweep-only outfits that clean and then refer structural work out; others are general contractors who take a chimney job occasionally. We sit in the middle of neither category: sweeping, repair, and inspection are the only three things we do, and repair is the largest part of that. So when you compare chimney repair companies in Vacaville, ask what they actually perform in-house and what brands they specify. We work with HeatShield, Gelco, Olympia Chimney, and Famco, which tells you what kind of repair we’re equipped to do. Most repair visits run about $300 to $1,500 depending on what’s found, and the written estimate sets the final price.
Questions to Ask Before You Book
Ask whether repairs are done by the same technicians who do the inspection, or subbed out. Ask what liner and resurfacing materials they use by name. And ask whether you’ll get photos of the problem before work begins; a specialist will say yes.

Scope of Work in the Written Estimate
A clear estimate lists each repair item, the material being used, and what happens if more damage turns up once the work is opened up. If a quote is a single round number with no breakdown, ask for one before you sign.
Chimney Masonry Repair
Chimney Masonry Repair covers the brickwork and mortar joints that make up the visible chimney stack, from the roofline up. You need it when mortar joints are recessed or crumbling, bricks are spalling and flaking, or the stack is leaning after years of weather. Repointing and brick replacement are the two main jobs: repointing rakes out the old mortar and packs in new, while spalled bricks get cut out and replaced. We match mortar color and composition so the finished repair doesn’t stand out, and we check the flue tile inside while the stack is open. Typical masonry repair runs about $600 to $2,500, depending on the number of courses and how much brick needs replacement. The written estimate sets the final price.
Signs of Spalling Brick
Spalling shows up as flaking faces and brick dust on the roof or ground below the stack. It’s moisture getting into the brick and pushing out as it dries. Once one face pops, that brick can’t be saved; it gets replaced.
Mortar Matching for Older Homes
Older Vacaville homes often have softer lime-based mortar than modern brick wants. Using the wrong mix can crack the brick faces around a repair. We match the existing mortar type before repointing.
Brands We Service
We install and work with DuraFlex stainless liner systems, and we know where they wear and how they’re sized for different appliances. We also work with HeatShield for chimney resurfacing and liner restoration, which covers repair categories a sweep-only service can’t touch. Gelco and Olympia Chimney components show up in our repair work as well, and Famco fits into the mix when the job calls for it.
Knowing these brands matters because it changes what we can fix instead of what we have to refer out. A resurfaced flue or a properly sized liner is a repair a generalist won’t attempt. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water staining on the ceiling or firebox. A dark ring on the ceiling near the chimney or rust in the firebox usually means water is getting past the crown, cap, or flashing. It won’t stop on its own, and the longer it runs, the more of the flue it damages.
- A strong smoky or creosote smell in the house. That smell often means a blocked flue, poor draft, or a liner that’s failed. Burning a fire before it’s checked can push smoke and carbon monoxide back into the room.
- Visible cracks in the crown or missing mortar joints. Cracks in the crown and crumbling mortar let water in and weaken the stack’s structure. Small cracks are cheaper to fix than a rebuilt chimney top.
- Rust streaks or a loose cap. Rust on the cap or stack means the coating has failed and water is inside. A cap that’s rattling or sitting crooked can come off in the next wind.
- Smoke rolling into the room instead of up the flue. A smoky fire usually means the flue is blocked, undersized, or the liner has collapsed. Stop using the fireplace until it’s inspected.
Our Process, Step by Step
- 1
Book the visit. We ask what you’ve noticed and when, and we set a time. Same-day appointments are available when the schedule allows, and the estimate is free.
- 2
Inspect with a camera. Our technicians run a camera down the flue and photograph what it finds, from the firebox to the cap. You see the same images we do, so nothing gets recommended without evidence you can check.
- 3
Walk you through the findings. We explain what’s damaged, what’s cosmetic, and what can safely wait. If a repair isn’t urgent, we tell you plainly.
- 4
Write the flat-price estimate. Each item is listed with the material and the price. The written estimate sets the final price, so nothing gets added later without your say-so.
- 5
Do the repair and hand over photos. We complete the work, clean up, and give you before-and-after photos for your records. If you’re selling the home, those photos work as documentation for the buyer or insurer.
How Much Does Chimney Repair Cost in Vacaville?
A typical chimney repair in Vacaville runs $300 to $1,500 for the most common jobs, and more involved work like relining or masonry rebuilds runs higher. Chimney cap installation is usually $185 to $450; chimney cap replacement about $200 to $500; chimney flashing repair $350 to $900; chimney crown repair $450 to $1,200; and chimney masonry repair $600 to $2,500. A full chimney liner installation is the largest job on the list, typically $2,400 to $6,500.
What affects the price most is how far the damage has gone. A crown crack caught early is a small repair; a crown crack that’s been running water into the flue for two winters might mean a liner too. Chimney height and roof pitch also play a part, since a taller stack or a steep roof takes longer to work safely. Material choice matters as well: a stainless multi-flue cap costs more than a single-flue one, and an insulated liner costs more than an uninsulated length.
How you avoid overpaying is simple: get the camera evidence before you approve anything. We don’t quote a liner or masonry rebuild off a glance from the ground. If a repair can wait, we say so in writing, and you decide when to book it.
Every free estimate includes the camera inspection, the photo report, and a flat price per item. Nothing gets added later without your approval. Call (844) 797-8347 for an exact quote.
Our Service Area Near Vacaville
We serve Vacaville and the towns around it, including Esparto, Davis, Woodland, Hartley, Allendale, Green Valley, El Macero, Monument Hills, and the University of California-Davis area. Scheduling is handled by appointment, and we book the next available slot when you call. If you’re comparing options for chimney repair outside Vacaville, the same process applies: camera inspection, photo report, and a flat-price written estimate. Call (844) 797-8347 to book.
Serving Vacaville, CA – Our Local Coverage Area
We serve Vacaville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Vacaville
Chimney repair is the structural work that fixes what’s damaged on a chimney, from the firebox up to the crown and cap. It covers caps, crowns, flashing, liners, mortar joints, and brickwork, and it’s separate from sweeping, which cleans what’s inside the flue. Repair is done when the camera inspection shows a problem that cleaning can’t solve. Call (844) 797-8347 to book a free estimate.
Most common repairs take a few hours to a single day, while a full reline or masonry rebuild can take two to three days. Cap replacement and flashing repair are usually same-day jobs; crown repair depends on the material curing time. Liner installation takes longer because the flue has to be prepped and sized first. We give you a realistic timeframe in the written estimate.
Most chimney repairs in Vacaville run $300 to $1,500, with relining and masonry rebuilds running higher. A cap is typically $185 to $450, flashing $350 to $900, a crown $450 to $1,200, and masonry $600 to $2,500; a liner runs $2,400 to $6,500. The written estimate sets the final price. Call (844) 797-8347 for an exact quote; estimates are free.
Yes. We install DuraFlex stainless liners and we use HeatShield for resurfacing and liner restoration, along with Gelco, Olympia Chimney, and Famco components. Knowing these materials means we can repair what a sweep-only service would have to refer out. If you’re not sure what’s in your flue, the camera inspection will tell you.
Same-day service is available when the schedule allows, and dispatch runs Sunday through Friday, 7am to 7pm. We’re closed on Saturday. Call (844) 797-8347 and we’ll book the next opening that works for you. We answer the phone 24/7.
Our repair work is backed by a satisfaction guarantee, and material coverage depends on the manufacturer’s terms for the product used. We explain the warranty for your specific repair when we go over the estimate. Nothing is promised verbally and left off the paperwork; it’s written down with the price.
Clear the fireplace opening and the floor in front of it, and move anything breakable away from the hearth. Keep pets and children out of the room while the camera and tools are out. If you have the paperwork from a previous sweep or inspection, have it ready; it helps us see what’s changed.
Schedule Your Chimney Repair Service in Vacaville Today
If something about your chimney looks wrong, whether it’s water staining, a loose cap, or a crack in the crown, we can take a look and tell you what it needs. The estimate is free, the inspection comes with photos, and the flat price is set in writing before any work starts. Call (844) 797-8347. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Vacaville.